Furnace Installation in Moore, OK | Free Estimates · A+ BBB · Licensed
New furnace installation with proper sizing, code-compliant venting, and matched-system efficiency. Free estimates. Serving Moore and the OKC metro since 2009. OK CIB #00125054. A+ BBB. 5.0★ from 111 5-star Google reviews.
Furnace Installation Service for Moore Homeowners
Furnace installation in Moore starts with a Manual J heat loss calculation — not a rule-of-thumb estimate. Moore's housing stock — 1960s–2000s from 2013 EF5 tornado, mix of original ranch-style and newer construction — means we see a wide range of duct conditions, fuel types, and venting configurations that affect system selection.
Fuel type in Moore: natural gas. We carry equipment and parts for both natural gas and propane systems. From our Edmond shop, we reach Moore in 30–40 min (30–45 minutes typical response).
Common Furnace Installation Issues We See in Moore
Furnace installation in Moore requires attention to the local housing stock and fuel availability — 1960s–2000s from 2013 EF5 tornado, mix of original ranch-style and newer construction. Key considerations:
- Manual J heat loss calculation based on actual Moore climate data and building characteristics
- Fuel type confirmation — natural gas
- Duct condition assessment before sizing
- Venting configuration for the chosen efficiency tier
Wrong-size furnace from a previous installer
The most common call we get from Moore in September and October. Nine times out of ten it's a failed capacitor — the $8 part that starts the compressor — or a refrigerant leak. We carry both on the truck. Refrigerant doesn't 'run low' on its own; if it's low, there's a leak that needs finding and sealing, not just a refill.
Improper venting on condensing furnaces
Refrigerant overcharge from a previous 'top-off' by another tech can actually prevent proper cooling — too much refrigerant is as bad as too little. We measure charge precisely and correct it either direction, not just add more.
No condensate management plan
Low voltage at the disconnect is a common cause of breaker trips in Moore — if the utility voltage is running low, the compressor draws more current to compensate. We measure supply voltage as part of every electrical diagnostic.
Inadequate combustion air
Dirty evaporator coils can cause freezing even with correct refrigerant charge in Moore — the restricted airflow drops coil temperature below freezing. We clean the evaporator coil as part of every freezing diagnosis because it's often the complete fix.
Mismatched gas pressure
Rattling from the ductwork in Moore homes is often loose sheet metal, a disconnected duct section, or a damper that's vibrating. We trace ductwork noise to the source — it's usually a 15-minute fix once located.
Our Furnace Installation Process for Moore Homeowners
- You call or textour team or a senior technician evaluates the existing furnace, ductwork, gas supply, venting, and combustion air. No high-pressure sales presentation.
- I come to youManual J heat loss based on home size, insulation, windows, and Oklahoma climate data. This determines correct BTU sizing — oversized furnaces are the most common installer mistake.
- Diagnosis first, quote secondTypically a budget 80% AFUE option, a value 95% AFUE option, and a premium 96-98% AFUE option. Itemized parts, labor, permit, and disposal — no surprise fees.
- Same-day repair when possibleMost replacements: one day (6-9 hours). New ductwork or venting changes: 1.5-2 days. Crew of 2. Old equipment removal, refrigerant recovery (if applicable), and recycling included.
- CommissioningManifold gas pressure check, combustion analysis (CO and CO2 ratio), temperature rise measurement across the heat exchanger, draft and venting verification, electrical safety check.
- Walkthrough and warrantyWe show you the readings, explain filter changes, walk through the thermostat, and register your manufacturer warranty (most 10-year parts).
Typical Furnace Installation Pricing in Moore, Oklahoma
- 80% AFUE single-stage (basic): $3,500-$4,800
- 95% AFUE single-stage condensing: $4,500-$5,500
- 96% AFUE two-stage: $4,800-$6,200
- 97-98% AFUE modulating variable-speed: $5,500-$7,500
- Add: PVC vent kit (for condensing furnace): +$200-$400
- Add: chimney liner (for 80% AFUE in old chimney): +$300-$600
- Add: new gas line section (if needed): +$150-$400
Financing from $79/month
We keep financing simple: 0% APR for those who qualify, fixed-rate options for 640+ credit, and secondary lenders for scores as low as 580. The soft-credit approval is same-day and leaves your score untouched until you accept terms — and you can pay off any tier early with no penalty.
See Financing DetailsWhat We See in Moore — Furnace Installation Patterns
Moore's post-2013 rebuild homes were sized correctly for their era. But 10 years later, some of those systems are undersized for additions and finished basements that weren't in the original plans. We re-calculate load before recommending any replacement.
Common furnace installation scenarios in Moore: replacing aging 80% AFUE systems with high-efficiency 96% AFUE units, converting from propane to natural gas where available, and right-sizing systems that were originally oversized or undersized.
Serving Moore Neighborhoods
Moore's neighborhoods reflect the community's history of rebuilding after the 1999 F5 and 2013 EF5 tornadoes. The pre-1999 neighborhoods — particularly in the areas that were directly affected — have been substantially rebuilt with 2000s to 2010s construction. The neighborhoods south of I-240 and east of Santa Fe Avenue are a mix of original 1960s to 1980s construction and post-tornado rebuilds. The newer Moore developments along 19th Street and in the eastern part of the city are 2000s to 2020s construction. We are familiar with the equipment that dominates each Moore neighborhood and the specific challenges of post-tornado construction.
Common Furnace Installation Issues in Moore
Moore's post-2013 rebuild homes were sized correctly for their era. But 10 years later, some of those systems are undersized for additions and finished basements that weren't in the original plans. We re-calculate load before recommending any replacement.
Common furnace installation scenarios in Moore: replacing aging 80% AFUE systems with high-efficiency 96% AFUE units, converting from propane to natural gas where available, and right-sizing systems that were originally oversized or undersized.
Moore Homeowners Ask About Furnace Installation
What Makes ARP Different for Moore Furnace Installation Calls
Most HVAC companies in the OKC metro are either large franchises with rotating staff or one-person operations without the parts inventory to fix things same-day. ARP sits in the middle: small enough that the owner is personally accountable for every job, large enough to carry a full parts inventory for all major brands. For Moore homeowners, that means a furnace installation call typically gets resolved in a single visit — no "we'll have to order that part" delays that leave you without AC for three days in August. ARP has maintained a 5.0-star Google rating across 111 reviews by keeping that standard consistent since 2009.
Do you serve Moore for furnace installation?
Yes — Moore is in our regular service area. From our Edmond shop, we reach Moore in 30–45 minutes via I-35. Same-day service is available for most Moore calls. We cover all Cleveland County ZIPs in Moore: 73160, 73165, 73170.
What kind of HVAC equipment is common in Moore homes?
Moore housing is primarily 1960s–2020s. Moore has two distinct housing generations: pre-tornado stock (1960s–1990s) in the western and northern areas, and post-2013 rebuilt homes with modern energy codes in the Plaza Towers, Briarwood, and. We factor this in when diagnosing and recommending equipment.
How much does furnace installation cost in Oklahoma?
Typical installed cost runs $3,500-$7,500. 80% AFUE single-stage: $3,500-$4,800. 95% AFUE condensing single-stage: $4,500-$5,500. 96% AFUE two-stage (most popular for OKC homes): $4,800-$6,200. Premium 97-98% modulating: $5,500-$7,500.
What efficiency furnace should I buy in Oklahoma?
For most OKC metro homes, 95% AFUE single-stage or 96% AFUE two-stage is the sweet spot. The gas savings over 80% AFUE typically pay back the upfront cost difference in 6-9 years. Going higher (97-98% modulating) makes sense if you have a larger home, value quieter operation, or plan to stay 10+ years.
Do I need to replace my AC at the same time?
Not necessarily. If your AC is under 8 years old and matched to the existing blower, you can replace just the furnace. If it is 12+ years old, replacing both at once usually makes economic sense — labor is roughly the same and you get matched-system warranty coverage.
How long does furnace installation take?
Most replacements: one day (6-9 hours). Installations requiring new venting (80% AFUE to 95%+ AFUE conversion), ductwork modifications, or electrical service changes typically take 1.5-2 days.
Do I need a permit for furnace installation?
Yes, in most OKC metro jurisdictions. We pull the permit, coordinate with the inspector, and handle the inspection. Permit cost is included in our quote — not a surprise add-on.
What about the federal tax credit for high-efficiency furnaces?
The federal 25C Energy Efficient Home Improvement Credit expired December 31, 2025 under the One Big Beautiful Bill Act. Furnace installations completed in 2026 or later do not qualify for federal tax credits. Oklahoma Natural Gas and OG&E utility rebates are now the primary savings pathway (up to $500-$2,500 depending on efficiency tier).
Do you offer financing for furnace installation?
Yes. From $79/month with same-day soft-credit approval. 0% APR options for qualified buyers (credit 700+). Standard fixed-rate financing for 640+. Secondary lender options down to 580 credit.
What brand of furnace do you recommend?
Carrier, Trane, and Lennox at premium tier. Goodman, Rheem, and Bryant at value tier. All major brands have comparable mid-range equipment. Brand matters less than correct sizing and proper installation.
What we factor into furnace installation quotes in Moore
Typical Moore housing stock
Moore's housing is mostly 1970s–2000s residential, with significant rebuilds after the May 1999 and May 2013 tornadoes. The rebuild-era homes (post-2013 especially) tend to have above-grade safe rooms or storm shelters in the garage, which we work around when servicing equipment.
What we typically see in Moore
We see a lot of post-tornado-rebuild homes here where the HVAC was contractor-package-deal equipment rather than spec'd for the house. By year 10–12 those systems often need replacement that was foreseeable from day one.
From our team
Typical response is 30–45 minutes from our Edmond shop. If you have a safe room in the garage, tell us when scheduling — we plan our truck space around it so we're not blocking your access during the service. Moore is in the heart of Tornado Alley; we use ground-level condenser pads with proper tie-downs as a standard here.
All HVAC Services in Moore, OK
AC Repair
$185-$650 typical
AC Installation
$4,000-$10,500 installed
AC Maintenance
$129 single visit · $189/year membership
Furnace Repair
$150-$800 typical
Heat Pump Services
$5,500-$12,500 installed; repair varies
Emergency HVAC
$89 diagnostic, no overtime — same as business hours
Ductless Mini-Splits
$3,500-$5,500 single-zone; $7,500-$14,000 multi-zone
Thermostat Services
$195-$450 installed
Indoor Air Quality
$250-$3,500 depending on scope
Commercial HVAC
Quote by project
Ventilation Services
Quote by project; basic seal $600-$1,200
Furnace Installation Coverage in Moore Neighborhoods
We provide furnace installation throughout Moore, including: Westmoore, Briarwood, Plaza Towers area, SW 4th Street corridor, Little River Park area, Heather Lakes . Response time from our Edmond shop is 30–45 minutes. Same-day service is available for most furnace installation calls in Moore.
Furnace Installation in Nearby OKC Metro Cities
Furnace Installation in Bethany
Oklahoma County · ~25–40 min drive
Furnace Installation in Edmond
Oklahoma County · ~15–25 min drive
Furnace Installation in Midwest City
Oklahoma County · ~25–40 min drive
Furnace Installation in Mustang
Canadian County · ~35–50 min drive
Furnace Installation in Norman
Cleveland County · ~35–50 min drive
Furnace Installation in Oklahoma City
Oklahoma County · ~25–45 min drive